![stm32 windows 10 driver stm32 windows 10 driver](https://2.bp.blogspot.com/-ILriKaqdvcM/WfTLrLeSJEI/AAAAAAAAB38/BG4NMCGsCxkmnjwqPCYszm_vJtcQ8ZlJwCEwYBhgL/s400/device%2Bmanager%255D.png)
I had no luck flashing the USB bootloader with a cheap USB to TTL but I was able to connect with an ST-Link and successfully flashed the generic_boot20_pc13.bin file. Anyway I thought I would purchase a couple maple mini boards from eBay. I'll of course try that if so, however can you confirm it?Īlso, if you could, please let me know if the procedure steps to do it is correct? (Asking again since you haven't replied to that)I am completely new to Arduino, although I have some experience flashing STM32 chips (I was able to fix an F4 flight controller and a Matek Sys video transmitter with burned out STM32 chips). If STM32 Cube gives drivers that's amazing. I get the Ding but the notification says USB device is unknown. No, it shows as a non identified USB device. Thanks sooooooooo much in advance once again. It's perfect if I can use USB cable only but at this rate, even the TTL thing is sufficient for me.
![stm32 windows 10 driver stm32 windows 10 driver](https://i.ytimg.com/vi/LwCzMqbjN6g/maxresdefault.jpg)
I'll wait for a reply before trying because I really don't want to damage my board if I can get it working. If you or someone knowledgeable can accurately mention the steps, it will be great help. Is this how it's supposed to be done then? Or should I just move the Boot0 when all the 4 TTL jumper cables are connected? (If I touch some pins accidentally, wouldn't it short circuit or damage the board somehow? The Boot0 jumper on the board requires a lot of pull to reposition.) Or is there a step to press the reset button?.Provide power again, perhaps using just Vin and Gnd jumpers from the TTL module.(two pins that are nearer to the Micro USB port) Upload the blink script using Arduino IDE.(two pins that are farther from the Micro USB port) Connect the 4 jumpers (Vin, Gnd, and Tx, Rx to A9, A10) with Boot0 at High.So even if I use a Serial TTL connection (Vin, Gnd, Tx, Rx), should I move the jumper to run? Can you please explain me if these steps are correct or wrong then? So there is still some hope!!:see_no_evil_monkey: If it helps, here's the store link that I bought it from. I'm really not keeping high hopes here, so you can surprise me. So please let me know if there's a way to download some software, drivers, or connect my stm32f103c8t6 with the components I have somehow and get it working. I just want to try once more to somehow get my stm32f103c8t6 working, or just throw it away and buy an Arduino board. I have a USB TTL (PL2303) adapter, several USB to micro USB cables, jumpers, breadboards, Resisters, Capacitors etc with me. What sort of a company doesn't develop drivers for Windows 10? :( I don't want to buy anymore adapters or other physical items because my initial happiness about stm32f103c8t6 is already gone. I tried searching everywhere for a solution, and all I found out is nothing.
![stm32 windows 10 driver stm32 windows 10 driver](https://i.ytimg.com/vi/zkVtTSt92Xc/hqdefault.jpg)
The blink example seems to upload to the stm32f103c8t6 without issues, but the LED pc13 does not blink. Used the Arduino IDE latest version like every instructional video says. I installed its drivers, and I connected using Vin, Gnd, Tx, Rx (A9, A10 pins) and tried to get it working. When I plug in my stm32f103c8t6 with USB cable and micro USB port, it shows USB device is not recognized. I tried the Windows 7 and Windows 8 drivers but they don't work. I'm using Windows 10 as I'm sure more than 75% of the world are. I can't even seem to get it connected with my PC. I read some glowing reviews about it and bought it as my first ever MCU because it was affordable. Hi, I'm completely new to MCU programming, and bought my very first unit stm32f103c8t6 from a local store.